| Codice materiale SAP | 5358451 |
| Codice catalogo ISO | SDR102 |
| Codice catalogo ANSI | SDR102 |
| Qualità | WDN00U |
| Taglienti per inserto | 1 |
| [LI] Lunghezza inserto | 22.2200 mm |
| [LI] Lunghezza inserto | .8740 in |
| [W] Larghezza dell’inserto | 9.5200 mm |
| [W] Larghezza dell’inserto | .3750 in |
| [Rε] Raggio di punta | 3.1700 mm |
| [Rε] Raggio di punta | .1250 in |
| Spessore medio del truciolo [HM] | 0.0200 mm |
| Spessore medio del truciolo [HM] | .0008 in |
An ultra-fine grained polycrystalline diamond (PCD) tip brazed onto a carbide substrate. Designed for general purpose turning of primarily non-ferrous materials. Applied over a wide range of continuous to interrupted cuts where superior surface finish is needed. Use on low to medium silicon content aluminium alloys, non-metallics, copper, brass, and zinc-based alloys. The ultra-fine grained diamond particle size enables superior surface finishes while ensuring the best mechanical shock resistance of any PCD cutting tool.
| Material Group | Light Machining | General Purpose | Heavy Machining | |||
| Geometry | Grade | Geometry | Grade | Geometry | Grade | |
| P1–P2 | – | – | – | – | – | – |
| P3–P4 | – | – | – | – | – | – |
| P5–P6 | – | – | – | – | – | – |
| M1–M2 | – | – | – | – | – | – |
| M3 | – | – | – | – | – | – |
| K1–K2 | – | – | – | – | – | – |
| K3 | – | – | – | – | – | – |
| N1–N2 | SDR…/EDR… | WDN00U | SDR…/EDR… | WDN00U | SDR…/EDR… | WDN00U |
| N3 | SDR…/EDR… | WDN00U | SDR…/EDR… | WDN00U | SDR…/EDR… | WDN00U |
| S1–S2 | – | – | – | – | – | – |
| S3 | – | – | – | – | – | – |
| S4 | – | – | – | – | – | – |
| H1 | – | – | – | – | – | – |
| ae/D1 = | 0,2 | 0,3 | 0,4 |
| fz-Factor | 1,5 | 1,3 | 1,0 |
| vc-Factor | 1,3 | 1,2 | 1,1 |
| Insert Geometry | Programmed Feed per Tooth (fz) at a % of Radial Depth of Cut (ae) | Insert Geometry | ||||||||||||||
| 10% | 20% | 30% | 40% | 50–100% | ||||||||||||
| SDR… | 0,08 | 0,17 | 0,33 | 0,06 | 0,13 | 0,25 | 0,06 | 0,11 | 0,22 | 0,05 | 0,10 | 0,20 | 0,05 | 0,10 | 0,20 | SDR… |
| EDR… | 0,08 | 0,17 | 0,33 | 0,06 | 0,13 | 0,25 | 0,06 | 0,11 | 0,22 | 0,05 | 0,10 | 0,20 | 0,05 | 0,10 | 0,20 | EDR… |
| Light Machining | General Purpose | Heavy Machining |
| ae/D1 = | 0,2 | 0,3 | 0,4 |
| fz-Factor | 1,5 | 1,3 | 1,0 |
| vc-Factor | 1,3 | 1,2 | 1,1 |
| ae/D1 = | 0.2 | 0.3 | 0.4 |
| fz-Factor | 1.5 | 1.3 | 1.0 |
| vc-Factor | 1.3 | 1.2 | 1.1 |
| Light Machining | General Purpose | Heavy Machining |
| Insert Geometry | Programmed Feed per Tooth (fz) at a % of Radial Depth of Cut (ae) | Insert Geometry | ||||||||||||||
| 10% | 20% | 30% | 40% | 50–100% | ||||||||||||
| SDR… | .003 | .007 | .011 | .003 | .005 | .008 | .002 | .004 | .007 | .002 | .004 | .006 | .002 | .004 | .006 | SDR… |
| EDR… | .003 | .007 | .011 | .003 | .005 | .008 | .002 | .004 | .007 | .002 | .004 | .006 | .002 | .004 | .006 | EDR… |
| ae/D1 = | 0.2 | 0.3 | 0.4 |
| fz-Factor | 1.5 | 1.3 | 1.0 |
| vc-Factor | 1.3 | 1.2 | 1.1 |
| ae/D1 = | 0,2 | 0,3 | 0,4 |
| fz-Factor | 1,5 | 1,3 | 1,0 |
| vc-Factor | 1,3 | 1,2 | 1,1 |
| ae/D1 = | 0,2 | 0,3 | 0,4 |
| fz-Factor | 1,5 | 1,3 | 1,0 |
| vc-Factor | 1,3 | 1,2 | 1,1 |
| Material Group | WDN00U | |||
| P | 1 | – | – | – |
| 2 | – | – | – | |
| 3 | – | – | – | |
| 4 | – | – | – | |
| 5 | – | – | – | |
| 6 | – | – | – | |
| M | 1 | – | – | – |
| 2 | – | – | – | |
| 3 | – | – | – | |
| K | 1 | – | – | – |
| 2 | – | – | – | |
| 3 | – | – | – | |
| N | 1–2 | 910 | 1980 | 4880 |
| 3 | 460 | 610 | 760 | |
| S | 1 | – | – | – |
| 2 | – | – | – | |
| 3 | – | – | – | |
| 4 | – | – | – | |
| H | 1 | – | – | – |
| ae/D1 = | 0.2 | 0.3 | 0.4 |
| fz-Factor | 1.5 | 1.3 | 1.0 |
| vc-Factor | 1.3 | 1.2 | 1.1 |
| Material Group | WDN00U | |||
| P | 1 | – | – | – |
| 2 | – | – | – | |
| 3 | – | – | – | |
| 4 | – | – | – | |
| 5 | – | – | – | |
| 6 | – | – | – | |
| M | 1 | – | – | – |
| 2 | – | – | – | |
| 3 | – | – | – | |
| K | 1 | – | – | – |
| 2 | – | – | – | |
| 3 | – | – | – | |
| N | 1–2 | 3000 | 6500 | 16000 |
| 3 | 1500 | 2000 | 2500 | |
| S | 1 | – | – | – |
| 2 | – | – | – | |
| 3 | – | – | – | |
| 4 | – | – | – | |
| H | 1 | – | – | – |
| ae/D1 = | 0.2 | 0.3 | 0.4 |
| fz-Factor | 1.5 | 1.3 | 1.0 |
| vc-Factor | 1.3 | 1.2 | 1.1 |
ISO Catalogo
ANSI Catalogo
to find similar products.Please select a file to download
. Please enter the desired qty for the material(s) you want to include in your promotion or Proceed Without Promotion and only your base materials will be added to the cart.
Minimum quantity should be
| SAP Material Number | ISO Catalogo | Grade |
|---|
You are about to leave the Solution building process.
Are you sure you want to leave?
