Bienvenue
Veuillez confirmer vos préférences
Mettre à jour les préférences

Suggestions de produit

Product Family suggestions

WIDIA à votre service

Call (833) 931-0077

Support Clients

Trouver les coordonnées des supports clients dans le monde

quick order warning
Enter a Material #, Customer Material #, or Catalog # (ANSI/ISO) to quickly add products to your cart.
Enter a Material #, Customer Material #, or Catalog # (ANSI/ISO) to quickly add products to your cart.
Enter a Material #, Customer Material #, or Catalog # (ANSI/ISO) to quickly add products to your cart.
Enter a Material #, Customer Material #, or Catalog # (ANSI/ISO) to quickly add products to your cart.
Enter a Material #, Customer Material #, or Catalog # (ANSI/ISO) to quickly add products to your cart.
Quick Order in Cart
Article(s) ajoutées avec succès au panier
Voir le panier
Article(s) are being added to the cart
Voir le panier
Pour les clients Américains et Canadiens, un supplément tarifaire sera ajouté à votre commande pour les outils de coupe et produits connexes.

Couple et puissance de la fraise à plaquette indexable KM

Pour fraise à plaquette indexable avec outil à changement rapide KM

These calculations are based upon theoretical values and are only intended for planning purposes. Actual results will vary. No responsibility from Kennametal is assumed.

Conversion of Workpiece Material Rockwell (Optional):
Metric
Inch

Conversion of Workpiece Material Rockwell (Optional)

Skip this step if you already know the Brinell hardness number(HB)
Characteristics of Workpiece Materials

Characteristics of Workpiece Materials

HB
PSI N/mm 2
Ultimate Strength shown for generic steel. Please enter the actual value of your workpiece material if available&#44 for better accuracy You may look up this info through websites such as www.matweb.com
End Mill Nomenclature

End Mill Nomenclature

in.mm.
in. mm.
in. mm.

Machining Conditions

sfm m/min
in.(DOC) mm (DOC)
in.(WOC) mm(WOC)
in. IPT (chip load) mm
Most Common Workpiece MaterialsCm at W/D ratios:
W/D < = 0.660.66 < W/D < 1.0W/D = 1.0
Aluminum alloys1.01.051.1
Carbon and alloy steels1.01.151.3
Cast irons1.01.151.3
Titanium alloys1.01.201.4
Stainless steel&#44 High-temperature alloys2.02.152.3
MillingDepth of cutFeed per toothCw
Category(min-max), in.(min-max), in.&nbsp;
Light0.020-0.1000.003-0.0061.1
Medium0.100-0.2000.006-0.0101.2
Heavy duty0.200-0.4000.010-0.0201.3
   
Direct Belt Drive.9
Back Gear Drive.75
Geared Head Drive.7-.8
Oil - Hydraulic Drive.6-.9

Safe Operating Conditions

lbN
lbN
ft lbNm
ft lbNm

Calculated Machining Conditions

RPM
(IPM)(no productivity formula)mm/min
in (chip load at the cut) mm/min
(IPM)(with productivity formula)mm/min
in.3/min MRRcm3/min3
in.2mm2

Calculated Required Power

lbf should not exceed Ft maxN
ft-lb should not exceed TpNm

Machining Power

HPckW
hpkW
Vous êtes sur le point d’ajouter à votre page mes solutions. Souhaitez-vous continuer ?
Select the destination where you want to move à.
Select the project where you want to add product(s) à.
Nouvelle Folder
    • Applied Filters:
    • Clear All

A folder with the name already exists.

Veuillez saisir un nom valide
Product(s) successfully added to project __PROJECT_NAME__
product-image
Please adjust the following properties from

catalogue ISO

catalogue ANSI

to find similar products.

The following files are available

Please select a file to download

Models

Product data

I have read and accepted the Terms & Conditions of use

Can’t find the file type you’re looking for?

Vous devez être connecté pour voir les informations de votre tableau de bord
Session expired due to inactivity, please login again
Le(s) produit(s) () que vous essayez d’ajouter au panier est/sont indisponible(s), veuillez Contacter le service client.
article(s) ajouté(s) avec succès au panier
View Cart

. Please enter the desired qty for the material(s) you want to include in your promotion or Proceed Without Promotion and only your base materials will be added to the cart.

Minimum quantity should be

SAP Material Number catalogue ISO Grade  

You are about to leave the Solution building process.

Are you sure you want to leave?

Workpiece Selection

Standard

ALL

Material

Select a Value

Hardness

--

      Hardness Scale

      --

        Permitted Groups :

        Group

        SubGroup

        Hardness (HB)

        Hardness (HRC)

        CancelOk