Couple et puissance des fraises monoblocs KM

Pour fraises hélicoïdales monoblocs avec angle positif - Angle d’attaque 0°, avec outil à changement rapide KM

These calculations are based upon theoretical values and are only intended for planning purposes. Actual results will vary. No responsibility from Kennametal is assumed.

Conversion of Workpiece Material Rockwell (Optional)

Skip this step if you already know the Brinell hardness number(HB)

Hardness HRB OR HRC into Brinell Hardness (HB)

Rockwell HRCRockwell HRB

Characteristics of Workpiece Materials

Brinell Hardness

Ultimate strength

PSI

End Mill Nomenclature

d₁ Effective cutting diameter

in. mm.

d_KM Input KM size

l₁ Distance from the centerline to the nose radius of the insert

in. mm.

l₂ Distance from the flange face to the nose radius of the insert

in. mm.

z_e Number of effective flutes

Machining Conditions

V_c Cutting speed

sfm m/min

a_p Axial Depth of cut

in.(DOC) mm (DOC)

a_e Radial width of cut

in.(WOC) mm(WOC)

f_z Required feed per tooth

in. IPT (chip load) mm

C_m Machinability factor

Most Common Workpiece Materials	Cm at W/D ratios:
Most Common Workpiece Materials	W/D < = 0.66	0.66 < W/D < 1.0	W/D = 1.0
Aluminum alloys	1.0	1.05	1.1
Carbon and alloy steels	1.0	1.15	1.3
Cast irons	1.0	1.15	1.3
Titanium alloys	1.0	1.20	1.4
Stainless steel&#44 High-temperature alloys	2.0	2.15	2.3

C_w Tool wear factor:

Milling	Depth of cut	Feed per tooth	C_w
Category	(min-max), in.	(min-max), in.
Light	0.020-0.100	0.003-0.006	1.1
Medium	0.100-0.200	0.006-0.010	1.2
Heavy duty	0.200-0.400	0.010-0.020	1.3

E Machine efficiency factor

Direct Belt Drive	.9
Back Gear Drive	.75
Geared Head Drive	.7-.8
Oil - Hydraulic Drive	.6-.9

Safe Operating Conditions

>C_L Empirical coefficient for load

>F_max Maximum permissible load applied to KM joint

lbN

>F_tmax Maximum permissible tangential force

lbN

>C_T Empirical coefficient for torque

>T_max Maximum permissible torque applied to KM joint

ft lbNm

>T_p Maximum permissible actual torque

ft lbNm

Calculated Machining Conditions

n Spindle speed

RPM

V_f Feed rate

(IPM)(no productivity formula)mm/min (no productivity formula)

Reduced feed per tooth

in (chip load at the cut) mm/min

F_p Feed rate

(IPM)(with productivity formula)mm/min

Q Metal removal rate

in.³/min MRRcm3/min³

A Cross-sectional area of chip

in.²mm²

Number of flutes in the cut

a_e/d₁ Ratio of radial width of cut to cutting diameter:

Calculated Required Power

F_t Tangential cutting force

lbf should not exceed Ft maxN should not exceed Ft max

T Actual torque

ft-lb should not exceed TpNm should not exceed Tp

Machining Power

at the cutter

HPckW

at the motor

hpkW

You are about to leave the Solution building process.

Are you sure you want to leave?

Bienvenue

Veuillez confirmer vos préférences

Mettre à jour les préférences

Suggestions de produit

Product Family suggestions

Call (833) 931-0077

Contacter le vendeur

Couple et puissance des fraises monoblocs KM

Pour fraises hélicoïdales monoblocs avec angle positif - Angle d’attaque 0°, avec outil à changement rapide KM

Conversion of Workpiece Material Rockwell (Optional)

Characteristics of Workpiece Materials

End Mill Nomenclature

Machining Conditions

Safe Operating Conditions

Calculated Machining Conditions

Calculated Required Power

Machining Power

Suggestions de produit

Product Family suggestions

Call (833) 931-0077

Contacter le vendeur

Notifications

Couple et puissance des fraises monoblocs KM

Pour fraises hélicoïdales monoblocs avec angle positif - Angle d’attaque 0°, avec outil à changement rapide KM

Conversion of Workpiece Material Rockwell (Optional)

Characteristics of Workpiece Materials

End Mill Nomenclature

Machining Conditions

Safe Operating Conditions

Calculated Machining Conditions

Calculated Required Power

Machining Power

The following files are available