VXF™-07 • シェルミル • メトリック
シェルミル • メトリック
使用法と用途
ポケット溝加工
100018357
ヘリカルミーリング
ランピング加工：ブランク
ミーリング — 側面および正面
Counter Boring
Spiral Circular
プランジミーリング
Inclined Square End Mill
フィルタと列
Filters
フィルタ
フィルタ表示
メートル
インチ
Workpiece Material
Workpiece Material
-
P Steel (2)
-
P0Low-Carbon Steels, Long Chipping C < .25%; <125 HB; <530 N/mm^2 UTS (2)
-
P1Low-Carbon Steels, Short Chipping C < .25%; <125 HB; <530 N/mm^2 UTS (2)
-
P2Medium and High Carbon Steels C < .25%; <220 HB; <25 HRC; >530 N/mm^2 UTS (2)
-
P3Alloy Steels & Tool Steels C > .25%; <330 HB; <35 HRC; 600-850 N/mm^2 UTS (2)
-
P4Alloy Steels & Tool Steels C > .25%; 350-420 HB; 35-43 HRC; 850-1400 N/mm^2 UTS (2)
-
P5Ferritic, Martensitic, and PH Stainless Steels <330 HB; <35 HRC; 600-900 N/mm^2 UTS (2)
-
P6High Strength Ferritic, Martensitic, and PH Stainless Steels 350-450 HB; 35-43 HRC; 900-2400 N/mm^2 UTS (2)
-
-
M Stainless Steel (2)
-
M1Austenitic Stainless Steel 130-200 HB; <600 N/mm^2 UTS (2)
-
M2High Strength Austenitic Stainless and Cast Stainless Steels 150-230 HB; <25 HRC; >600 N/mm^2 UTS (2)
-
M3Duplex Stainless Steel 135-275 HB; <30 HRC; 500-1200 N/mm^2 UTS (2)
-
-
K Cast Iron (2)
-
K1Gray Cast Iron 120-290 HB; <32 HRC; 125-500 N/mm^2 UTS (2)
-
K2Low and Medium Strength CGI and Ductile Irons 130-260 HB; <28 HRC; <600 N/mm^2 UTS (2)
-
K3High Strength Ductile and Austempered Ductile Iron 180-350 HB; <43 HRC; >600 N/mm^2 UTS (2)
-
-
N Non-Ferrous Materials (2)
-
N1Wrought Aluminum (2)
-
N2Low-Silicon Aluminum Alloys and Magnesium Alloys Si <12.2% (2)
-
N3High-Silicon Aluminum Alloys Si >12.2% (2)
-
-
S High-Temp Alloys (2)
-
S1Iron-Based, Heat-Resistant Alloys 160-260 HB; 25-48 HRC; 500-1200 N/mm^2 UTS (2)
-
S2Cobalt-Based, Heat-Resistant Alloys 250-450 HB; 25-48 HRC; 1000-1450 N/mm^2 UTS (2)
-
S3Nickel-Based, Heat Resistant Alloys 160-450 HB; <48 HRC; 600-1700 N/mm^2 UTS (2)
-
S4Titanium and Titanium Alloys 300-400 HB; 33-43 HRC; 900-1600 N/mm^2 UTS (2)
-
-
H Hardened Materials (2)
-
H1Hardened Materials 44-48 HRC (2)
-
Cutting Diameter
Cutting Diameter
-
1.204 in (1)
-
1.597 in (1)
to
Cutting Diameter
Cutting Diameter
-
30.576 mm (1)
-
40.575 mm (1)
to
Maximum Cutting Diameter
Maximum Cutting Diameter
-
40.0 mm (1)
-
50.0 mm (1)
to
Maximum Cutting Diameter
Maximum Cutting Diameter
-
1.575 in (1)
-
1.969 in (1)
to
Reach
Reach
-
1.26 in (1)
-
1.575 in (1)
to
Reach
Reach
-
32.0 mm (1)
-
40.0 mm (1)
to
Number of Flutes
Number of Flutes
-
5 (1)
-
7 (1)
Over All Length [L]
Over All Length [L]
-
1.26 in (1)
-
1.575 in (1)
to
Over All Length [L]
Over All Length [L]
-
32.0 mm (1)
-
40.0 mm (1)
to
Corner Radius
Corner Radius
-
0.031 in (2)
-
0.039 in (2)
to
Corner Radius
Corner Radius
-
0.8 mm (2)
-
1.0 mm (2)
to
application
Grade Of Cutting Tool
Grade Of Cutting Tool
-
WP25PM (2)
-
WP40PM (2)
-
WS40PM (2)
-
WU10PM (2)
Maximum Ramp Angle
Maximum Ramp Angle
-
0.7 (1)
-
1.0 (1)
to
backEnd
Back-End Diameter
Back-End Diameter
-
16.0 mm (1)
-
22.0 mm (1)
to
Back-End Diameter
Back-End Diameter
-
0.63 in (1)
-
0.866 in (1)
to
No filters matching ""
以下に示すパラメータのいずれかを使用して表示列を変更することができます。最大7列まで表示できます。
表示
1-
2
/
2 結果
メートル
インチ
表示
メートル
インチ
| SAP Material Number | ISO Catalog Number | ANSI Catalog Number | [D1] Effective Cutting Diameter | [D1] Effective Cutting Diameter | [L] Overall Length | [L] Overall Length | [D] Adapter / Shank / Bore Diameter | [D] Adapter / Shank / Bore Diameter | [D6] Hub Diameter | [D6] Hub Diameter | [AP1MAX] 1st Maximum Cutting Depth | [AP1MAX] 1st Maximum Cutting Depth | [D1MAX] Maximum Cutting Diameter | [D1MAX] Maximum Cutting Diameter | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 6597158 | VXF040Z05S16XP07 | VXF040Z05S16XP07 | 30.573 | 1.203 | 32 | 1.259 | 16 | .6299 | 37 | 1.456 | 0.9 | .0354 | 40 | 1.574 |
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
定価:
$443.12
/各
価格::
数量
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 6597159 | VXF050Z07S22XP07 | VXF050Z07S22XP07 | 40.57 | 1.597 | 40 | 1.574 | 22 | .8661 | 42 | 1.653 | 0.9 | .0355 | 50 | 1.968 |
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
定価:
$552.74
/各
価格::
数量
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
インサート選択の手引き
| Light
|
General
|
Heavy
|
||||
| Material
|
Geometry | Grade | Geometry | Grade | Geometry | Grade |
| P1–P2 | XPPT-MM | WP25PM | XPPT-MM | WS40PM | XPPW-MH | WP40PM |
| P3–P4 | XPPT-MM | WP25PM | XPPT-MM | WS40PM | XPPW-MH | WP40PM |
| P5–P6 | XPPT-MM | WP25PM | XPPT-MM | WS40PM | XPPW-MH | WP40PM |
| M1–M2 | XPPT-MM | WS40PM | XPPT-MM | WS40PM | XPPW-MH | WP40PM |
| M3 | XPPT-MM | WS40PM | XPPT-MM | WS40PM | XPPW-MH | WP40PM |
| K1–K2 | XPPW-MH | WU10PM | XPPW-MH | WU10PM | XPPW-MH | WU10PM |
| K3 | XPPW-MH | WU10PM | XPPW-MH | WU10PM | XPPW-MH | WU10PM |
| S1–S2 | XPPT-MM | WP25PM | XPPT-MM | WS40PM | – | – |
| S3 | XPPT-MM | WS40PM | XPPT-MM | WS40PM | – | – |
| S4 | XPPT-MM | WS40PM | XPPT-MM | WS40PM | – | – |
| H1 | XPPW-MH | WU10PM | XPPW-MH | WU10PM | – | – |
| Insert Geometry | Recommended Starting Feed per Tooth (Fz) in Relation to % of Radial Engagement (ae) | Insert Geometry | ||||||||||||||
| 5 % | 10 % | 20 % | 30 % | 40–100 % | ||||||||||||
| .E..MM | 0,46 | 1,32 | 2,43 | 0,32 | 0,89 | 1,53 | 0,24 | 0,65 | 1,09 | 0,21 | 0,56 | 0,94 | 0,19 | 0,52 | 0,85 | .E..MM |
| .S..MH | 0,84 | 1,84 | 3,12 | 0,59 | 1,21 | 1,85 | 0,43 | 0,87 | 1,30 | 0,38 | 0,75 | 1,12 | 0,34 | 0,69 | 1,02 | .S..MH |
| Insert Geometry | Recommended Starting Feed per Tooth (Fz) in Relation to % of Radial Engagement (ae) | Insert Geometry | ||||||||||||||
| 5 % | 10 % | 20 % | 30 % | 40–100 % | ||||||||||||
| .E..MM | 0,42 | 1,21 | 2,20 | 0,30 | 0,83 | 1,41 | 0,22 | 0,60 | 1,01 | 0,19 | 0,52 | 0,87 | 0,18 | 0,48 | 0,79 | .E..MM |
| .S..MH | 0,78 | 1,68 | 2,79 | 0,55 | 1,12 | 1,71 | 0,40 | 0,81 | 1,21 | 0,35 | 0,70 | 1,04 | 0,32 | 0,64 | 0,94 | .S..MH |
| Light
|
General
|
Heavy
|
| Insert Geometry | Recommended Starting Feed per Tooth (Fz) in Relation to % of Radial Engagement (ae) | Insert Geometry | ||||||||||||||
| 5% | 10% | 20% | 30% | 40–100% | ||||||||||||
| .E..MM | 0,37 | 1,06 | 1,89 | 0,27 | 0,73 | 1,24 | 0,20 | 0,53 | 0,89 | 0,17 | 0,46 | 0,77 | 0,16 | 0,42 | 0,70 | .E..MM |
| .S..MH | 0,68 | 1,46 | 2,35 | 0,48 | 0,98 | 1,49 | 0,36 | 0,71 | 1,07 | 0,31 | 0,62 | 0,92 | 0,28 | 0,56 | 0,84 | .S..MH |
| Insert Geometry | Recommended Starting Feed per Tooth (Fz) in Relation to % of Radial Engagement (ae) | Insert Geometry | ||||||||||||||
| 5% | 10% | 20% | 30% | 40–100% | ||||||||||||
| .E..MM | .020 | .058 | .109 | .014 | .039 | .067 | .010 | .028 | .047 | .009 | .025 | .041 | .008 | .022 | .037 | .E..MM |
| .S..MH | .036 | .080 | .141 | .025 | .052 | .080 | .019 | .037 | .056 | .016 | .032 | .048 | .015 | .029 | .043 | .S..MH |
| Light
|
General
|
Heavy
|
| Insert Geometry | Recommended Starting Feed per Tooth (Fz) in Relation to % of Radial Engagement (ae) | Insert Geometry | ||||||||||||||
| 5% | 10% | 20% | 30% | 40–100% | ||||||||||||
| .E..MM | .018 | .051 | .094 | .013 | .035 | .059 | .009 | .025 | .042 | .008 | .022 | .037 | .007 | .020 | .033 | .E..MM |
| .S..MH | .032 | .070 | .118 | .023 | .046 | .071 | .017 | .033 | .050 | .014 | .029 | .043 | .013 | .026 | .039 | .S..MH |
| Insert Geometry | Recommended Starting Feed per Tooth (Fz) in Relation to % of Radial Engagement (ae) | Insert Geometry | ||||||||||||||
| 5% | 10% | 20% | 30% | 40–100% | ||||||||||||
| .E..MM | .015 | .043 | .076 | .011 | .029 | .050 | .008 | .022 | .036 | .007 | .019 | .031 | .006 | .017 | .028 | .E..MM |
| .S..MH | .027 | .058 | .093 | .019 | .039 | .059 | .014 | .028 | .042 | .012 | .024 | .036 | .011 | .022 | .033 | .S..MH |
推奨切削速度の開始値［m/min］*
| Material Group | WP25PM | WP40PM | WS40PM | WU10PM | |||||||||
| P | 1 | 395 | 340 | 325 | 355 | 310 | 295 | – | – | – | – | – | – |
| 2 | 330 | 290 | 240 | 300 | 260 | 215 | – | – | – | – | – | – | |
| 3 | 305 | 260 | 210 | 275 | 235 | 190 | – | – | – | – | – | – | |
| 4 | 270 | 220 | 180 | 245 | 205 | 160 | – | – | – | – | – | – | |
| 5 | 220 | 205 | 180 | 205 | 185 | 160 | 205 | 175 | 145 | – | – | – | |
| 6 | 200 | 150 | 120 | 180 | 140 | 110 | 180 | 130 | 95 | – | – | – | |
| M | 1 | 245 | 215 | 200 | 235 | 205 | 185 | 250 | 205 | 170 | – | – | – |
| 2 | 220 | 190 | 155 | 210 | 180 | 150 | 215 | 175 | 145 | – | – | – | |
| 3 | 170 | 145 | 115 | 155 | 140 | 110 | 175 | 130 | 100 | – | – | – | |
| K | 1 | 275 | 245 | 220 | – | – | – | – | – | – | 355 | 320 | 290 |
| 2 | 215 | 190 | 180 | – | – | – | – | – | – | 275 | 245 | 230 | |
| 3 | 180 | 160 | 145 | – | – | – | – | – | – | 235 | 210 | 190 | |
| S | 1 | 50 | 40 | 30 | 50 | 40 | 35 | 50 | 40 | 30 | – | – | – |
| 2 | 50 | 40 | 30 | 50 | 40 | 35 | 50 | 40 | 30 | – | – | – | |
| 3 | 60 | 50 | 30 | 60 | 50 | 35 | 60 | 50 | 30 | – | – | – | |
| 4 | 85 | 60 | 40 | 80 | 60 | 40 | 70 | 60 | 35 | – | – | – | |
| H | 1 | 145 | 110 | 85 | – | – | – | – | – | – | 190 | 155 | 110 |
Recommended Starting Speeds [SFM]*
| Material Group | WP25PM | WP40PM | WS40PM | WU10PM | |||||||||
| P | 1 | 1295 | 1115 | 1065 | 1165 | 1015 | 970 | 1085 | 920 | 785 | – | – | – |
| 2 | 1085 | 950 | 785 | 985 | 855 | 705 | 900 | 805 | 605 | – | – | – | |
| 3 | 1000 | 855 | 690 | 900 | 770 | 625 | 835 | 705 | 540 | – | – | – | |
| 4 | 885 | 720 | 590 | 805 | 675 | 525 | 755 | 625 | 490 | – | – | – | |
| 5 | 720 | 675 | 590 | 675 | 605 | 525 | 675 | 575 | 475 | – | – | – | |
| 6 | 655 | 490 | 395 | 590 | 460 | 360 | 590 | 425 | 310 | – | – | – | |
| M | 1 | 805 | 705 | 655 | 770 | 675 | 605 | 820 | 675 | 560 | – | – | – |
| 2 | 720 | 625 | 510 | 690 | 590 | 490 | 705 | 575 | 475 | – | – | – | |
| 3 | 560 | 475 | 375 | 510 | 460 | 360 | 575 | 425 | 330 | – | – | – | |
| K | 1 | 900 | 805 | 720 | – | – | – | – | – | – | 1165 | 1050 | 950 |
| 2 | 705 | 625 | 590 | – | – | – | – | – | – | 900 | 805 | 755 | |
| 3 | 590 | 525 | 475 | – | – | – | – | – | – | 770 | 690 | 625 | |
| S | 1 | 165 | 130 | 100 | 165 | 130 | 115 | 165 | 130 | 100 | – | – | – |
| 2 | 165 | 130 | 100 | 165 | 130 | 115 | 165 | 130 | 100 | – | – | – | |
| 3 | 195 | 165 | 100 | 195 | 165 | 115 | 195 | 165 | 100 | – | – | – | |
| 4 | 280 | 195 | 130 | 260 | 195 | 130 | 230 | 195 | 115 | – | – | – | |
| H | 1 | 475 | 360 | 280 | – | – | – | – | – | – | 625 | 510 | 360 |